What does a Florida roofing permit review look for?

A Florida roofing permit review checks whether the products are approved for the way they will be used on this roof, and whether the wind design matches the code for that parcel and the edition named on the permit. Marion County is not the High-Velocity Hurricane Zone. Miami-Dade and Broward are. Which local office takes the application is a different question from what the state code asks the design to show. This page is the statewide review. It is not a substitute for the office that has the lot.

The code edition is the one printed on the permit

As of this review on September 24, 2026, the edition in force is the 8th Edition (2023) Florida Building Code. The 9th Edition is scheduled for December 31, 2026. Confirm the edition on the permit. Do not assume a website date matched your application. The Florida Building Commission publishes the code at https://floridabuilding.org.

A house roof is reviewed under the roofing requirements of that edition. An existing roof being replaced is also in the existing-building provisions. Read the section that matches the permit. Do not carry an old detail forward, and do not substitute a Miami-Dade reroof chapter for the section that applies in Marion County.

Product approval has to match this roof

Florida Statutes section 553.842 is the statewide product evaluation and approval system. Roofing is one of the categories that statute names. An approval is not a logo. It is a statement that the product met the code when used as tested: the deck, the slope, the underlayment, the fasteners, and the limits written on the approval. Use it outside those conditions and you are not using the approval.

This page prints no product approval numbers. A number from another house may be the wrong slope, deck, or design pressure. The submittal names the approval for the covering and the underlayment, and shows fastening that meets the wind design. Statewide approval, used as approved, limits a local demand for a second test of that product. The paperwork should say which approval path is offered.

A Miami-Dade notice of acceptance is an approval path of the High-Velocity Hurricane Zone. A product may hold a Florida approval, a notice of acceptance, or both. Holding a notice of acceptance does not move Marion County into that zone, and it does not make that zone’s reroof chapters the installation manual for an Ocala house. Install the product the way its Florida approval and this site’s wind design require.

Wind design is calculated for the parcel

The code edition contains the wind maps and the method for the site. Height, exposure, and roof shape change the result. A hip and a gable are not the same pressures. A one-story ranch and a taller roof are not the same calculation. This page does not state a wind speed. A speed remembered from a coastal county is not this permit.

Exposure is a code category, not a slogan. Trees are not a free pass to nail the roof for a calm day, and an open field is not a reason to import a High-Velocity Hurricane Zone schedule. The shingle nail count, or the clip spacing on metal, has to meet the pressures from the design and the limits on the product approval. If those two documents do not agree, the roof is not designed yet.

Marion County is not the High-Velocity Hurricane Zone

The High-Velocity Hurricane Zone is Miami-Dade and Broward only. It is not Marion County, Ocala, Belleview, or Dunnellon. Test protocols and reroof chapters for that zone are not the inland default. Using them invents requirements. Ignoring wind design because the lot is inland leaves the opposite hole. Underlayment, fastening, flashing, and product approval are still reviewed under the edition on the permit.

What a site visit has to record for the permit

The application describes one roof, so the visit records the facts that make it true. The address is the parcel, not the ZIP code. Slope is measured on every plane that will be covered, including a low porch. Height and roof shape go into the wind design. Layers are recorded so the scope is a repair, a tear-off, or not yet nameable. From the attic, where entry is safe, the deck is noted. Penetrations and walls are counted because they are flashing. Photos are a file, not the product approval and not the calculation. If a needed fact cannot be seen, it is not invented. The permit card lists the inspections. Covered work an inspector still needs to see stays open. This page does not invent inspection names.

• Parcel address, so the office and the wind site match
• Slope, height, and roof shape for the design
• Existing layers, and whether the scope is a tear-off
• Deck type, if it can be seen without guessing
• Penetrations and walls the approval has to cover
• The product approval and fastening that match those facts

Which counter you use is the local page

Ocala, Belleview, Dunnellon, and unincorporated Marion County are different building departments. An Ocala ZIP code is not the test. Unincorporated Marion County publishes its own examples of work that may not need a permit, including a small roof repair, and that county note does not apply inside a city. The office and that exception are on the local roofing permits page. A full replacement is permit work. The assembly is the roof replacement page. What changes the scope is roof replacement cost. The permit is not a bid.

Who is allowed to pull the roofing work

Ocala Building Contractor holds Florida certified building contractor license CBC1263067. Under Florida Statutes section 489.105, that license covers buildings not exceeding three stories, accessory structures, and remodeling or repair of any size if the structural members are not affected. Roofing-only licenses are separate. This company is not a roofing contractor. When it takes roofing, that trade is subcontracted to a licensed roofer. The permit should name the licenses the office requires. Owner-builder status exists with conditions. This page will not write steps for skipping a contractor. Firm records are on the licenses and insurance page.

Mistakes that paste a coastal sheet onto an inland permit

One mistake is filing a Miami-Dade reroof detail as if Marion County used that chapter. Another is borrowing an approval from a different slope, or designing wind for the wrong height because the form was faster. Another is starting work before the office that has the parcel has issued the permit.

• Treating a notice of acceptance as the Marion County code
• Leaving the approval unnamed, or copying one
• Stating a wind speed from memory
• Using the mailing address instead of the parcel
• Covering work an inspector has not seen
• Calling a building contractor license a roofing license

Decisions before the application is filed

• Confirm the office on the local permit page, from the parcel
• Confirm the code edition the office will apply
• Match each product approval to this deck and this slope
• Run the wind design for this building, and do not invent a speed
• Keep High-Velocity Hurricane Zone chapters out of a Marion County set
• Name the roofing subcontractor’s license if this firm is the contractor

Sources for the statewide review

Code edition and publication: Florida Building Commission, https://floridabuilding.org. Product evaluation and approval, including roofing as a category: Florida Statutes section 553.842, https://www.flsenate.gov/Laws/Statutes/2025/553.842. Certified building contractor scope: Florida Statutes section 489.105, https://www.flsenate.gov/Laws/Statutes/2025/489.105. The county’s own permit examples, which this page does not restate as a city rule, are at https://www.marionfl.org/agencies-departments/departments-facilities-offices/building-safety/permitting-faqs.